Installation Accessories

  • A single component aerosol foam for the filling of anchor bolt isolation cans or PVC sleeves for adequate anchor bolt stretch during machinery installation. Also used to prevent future corrosion of the anchor bolt that has been embedded in the epoxy or cement grout.
  • We can makes up custom damming forms for our chocking compounds. These are typically made of angle iron pieces to disipate the temperatures of epoxy exotherm during the curing process
  • We carry a complete series of finish brushes for the application of our industrial, commercial, and marine coatings. Call us with your product application and we can recommend the right bruch for the application.
  • We carry a series of epoxy compounds for the setting of our injection ports. Call us with your application and we can make a recommendation of the right product for the installation.
  • A 20 oz. manual sausage or bulk loading gun w/ smooth and efficient 12:1 ratio drive. Full size handle for applicator comfort and efficient dispensing. Aluminum swivel barrel that exerts 120 psi pressure and 375 lbs. of thrust. Available with bulk loading sleeve for easy loading of cylinder and simple cleanup before dispensing.
  • A 20 oz. (600ml) sausage pack dispensing gun. Heavy duty dent resistant steel barrel swivels for dispensing convenience. Built with a #21-20 Teflon piston for sausage or bulk dispensing. Available with bent plastic cones for applicator comfort. Available with bulk loading sleeve for easy loading of cylinder and simple cleanup before dispensing.
  • Designed for use in a grout pumping application for quick connect/disconnect of hoses for product installation or easy removal to clean out hoses after application. Also makes it simple to add additional lengths as required for the grout application. These fittings are manufactured from polypropylene plastic and work in a temperature range from -20 Deg. to 150 Deg. F. Used specifically for lay-flat hose with hose clamp connections. Characteristics: - Connections: Male Plug w/ barbed male end for layflat hose applications - Operating temperatures: -20 to 150 Deg. F - Maximum operating pressure is 125 psi - For use with polyurethane, Polyethylene, PVC, and Rubber hose - Meets Federal Specification A-A-59326 - Available with locking or Non-Locking Levers
  • Designed for use in a grout pumping application for quick connect/disconnect of hoses for product installation or easy removal to clean out hoses after application. Also makes it simple to add additional lengths as required for the grout application. These fittings are manufactured from polypropylene plastic and work in a temperature range from -20 Deg. to 150 Deg. F. F. Characteristics: - Connections: Female socket w/ NPT female end - Operating temperatures: -20 to 150 Deg. F - Maximum operating pressure is 125 psi - For use with Lay-Flat polyurethane, polyethylene, PVC, and rubber hose - Meets Federal Specification A-A-59326 - Available with locking or Non-Locking Levers
  • We carry a complete series of pneumatic and manual caulking guns for all of our plural component cartridge systems. These include cartridge sizes such as 750ml x 750ml, 750ml x 300ml, 750ml x 75ml, 600ml x 600ml, 600ml x 300ml, 300ml x 300ml,150ml x 150ml, 150ml x 75ml, 75ml x 75ml, etc. Call us for the right sizing of your application gun to the product you are dispensing.
  • We carry a complete series of single cartridge pneumatic and manual caulking guns. These include 10oz. Cartridges, 30oz. Cartridges, bulk loading/sausage guns. Call us for the right gun for your product application.
  • These are empty fiber-body caulking tubes w/ backing plates for the application of very fluid epoxy products for the resin injection process and mastic sealants such as control joint fillers or two part fairing compounds. Used with a normal 30 oz., 14:1 ratio, single cartridge, caulking guns.
  • We carry various bonding agents for bonding new overlay concrete to existing substrate. Fast set for use in colder ambient and surface temperatures to
  • We carry a complete series of throw away brushes used to clean or apply primer coats or industrial/commerial coatings not requiring an architectural finish. Call us with your application and product and we can make a brush recommendation.
  • We carry a number of cleanup media for our grouting and coating systems. This includes light household grade detergents for the cleanup of mixing and application equipment to microbial cleaners and super absorbant polymers for the cleanup of hydrocarbons and food based fats, oils, and grease. They leave behind only water. The super absorbent polymer soaks up to 25 gallons of contaminated water per pound of powder used. In short our products turn hazardous waste into manageable waste and helping to keep our enviroment clean.
  • We carry a number of high evaporative solvents for the cleanup of equipment and application tools for our coating and grouting systems. This includes our IXT59 solvent, J58 Citrus Cleaner, Mineral Spirits, Crown Pro Thinner (replaces MEK & Toluene), and standard acetone.
  • We carry a number of thinning solvents for our coating systems. This includes our Crown Pro Thinner (replaces MEK & Toluene), standard mineral spirits, acetone, and laquer thinner.
  • We carry all of the necessary tools to apply our various coatings systems. This includes tools such as nap rollers, core rollers, roller handles, gage rakes, gage boxes, notched trowels, and notched squeeges.
  • We carry a custom designed contractors hoe that helps eliminate the fatigue of mixing epoxy grout by hand using a standard yard hoe.
  • We carry all makes and models of contractors wheel barrows that have proven to be the most reliable pieces of equipment for the delivery of our grouting systems. This includes the standard single wheels 6 Cu. Ft. steel hopper to our 2 wheel 6 Cu. Ft polybarrel model. The dual wheel model provides a much improved stability over rough surfaces for the delivery our our epoxy grouts.
  • J62 is an epoxy rebar spray to prevent corrosion of rebar during the application of our cement structural concretes and grouts. It is green in color for easy identification of coverage. It is ozone safe and a no run formula. It is also fast drying.
  • We can help the project contractor with the design of his forming system. From single use forms to multi use systems to help curb the contractors cost for grout placement on the project site.We utilize standard wood systems as well as styrofoam forming for grout placement, control joints, safety chamfer edging, etc.
  • We can supply all application tools necessary for the placement of our epoxy and cement grouts. This includes masonry trowels, edging tools, contractors hoe, mixing boxes, putty knives (plastic or metal)